Electrical Conversion Efficiency Research Articles

Electrical energy efficiency of dye sensitized solar cells by polymer electrolyte

This research aims to prepare by mixtures method with dope carbon black as a working electrode and the apply it to the dye sensitized solar cells (DSSCs). The thin film of titanium dioxide nanocrystalline semi - conductor with dope carbon black, the cells were coated on to transparent conducting oxide glass sheet by means of the doctor blade technique as a working electrode. But the polymer electrolyte were prepare by adding potassium iodide and iodine salts with a ratio of KI:I2 was 10:1, into a polymer electrolyte composed of poly-ethylene glycol, ethylene carbonate and poly(styrene–co–acrylonitrile). The polymer electrolyte mixtures became homogeneous and stirring at a temperature of 80 °C.  Found that efficiency for the DSSCs by polymer electrolyte based on yielded an overall light to electrical energy conversion efficiency ( ) of the DSSCs was 5.5095%, An open-circuit voltage  of 0.58 V, voltage at the point of maximum power output  of 0.42 V, short-circuit current density  of 11.11 mA.cm–2, current density at the point of maximum power output  of 10.50 mA.cm–2 fill factor  of 0.684 under an irradiation of 80 mW.cm–2. And the long-term stability test of the DSSCs with a polymer electrolyte is evidently superior to the DSSCs with liquid electrolyte based on the observation period lasting for 90 days. GRAPHICAL ABSTRACT HIGHLIGHTS prepare by mixtures method with dope carbon black as a working electrode The efficiency for the DSSCs by polymer electrolyte based on yielded an overall light to electrical energy conversion

Improve The Conversion Efficiency and Electrical Output of The Solar PV System by Developing and Implementing a Cooling System

The performance of the grid-connected solar photovoltaic (PV) system in the present study is improved using cooling technology. This technology reduces the temperature of solar PV modules and thus increases their efficiency and lifespan. The current solar PV system has been installed in northern Baghdad in the city of Taji. This study included improving electrical power, conversion efficiency, and performance ratio. All of these improvements are achieved by cooling using water. The performance ratio (PR) and efficiency maximum values of the reference (unimproved) and improved solar PV modules are at 10:10 am at 88.30% & 96.30% and 13.4% & 14.6%, respectively. Improved and reference PV modules maximum solar radiation values occur at 12:00 pm at 1.91 W and 1.566 W, respectively. The maximum solar radiation values of  the reference and improved PV modules are at 12:00 pm at 922.9 W/m2 and 1012.22 W/m2, respectively. The maximum daily gain of the power and solar irradiance are 22% and 10%, respectively. The significant innovation in the study is the successful performance optimization of the grid-connected solar PV system. Using different equations to study performance by following different behaviors. Along with improving and studying CIGS PV module performance.

Enhanced dye-sensitized solar cell performance and electrochemical capacitive behavior of bi-functional ZnO/NiO/Co3O4 ternary nanocomposite prepared by chemical co-precipitation method

Increasing prerequisites for sustainable energy storage and conversion technologies have necessitated the exploration of advanced materials with improved properties. Here, we present the synthesis and characterization of ZnO nanoparticles (NPs), ZnO/NiO, ZnO/Co3O4 and ZnO/NiO/Co3O4 NCs as promising bi-functional materials for dye-sensitized solar cell (DSSC) and electrochemical energy storage applications. A facile chemical co-precipitation approach was followed to synthesize pure ZnO NPs, ZnO/NiO, ZnO/Co3O4 and ZnO/NiO/Co3O4 NCs. The structural and morphological analyses revealed the successful integration of ZnO, NiO, and Co3O4 NPs and also the formation of well-defined core-shell and homogenous nanocomposite structures. The XRD and HRTEM analyses confirmed the crystalline nature and nanoscale morphology of synthesized materials, respectively. The photovoltaic performance of DSSC fabricated using ternary ZnO/NiO/Co3O4 NC photoanode showed optimum dye-loading and best solar to electrical energy conversion efficiency with Jsc of 11.29 mA cm−2 and ƞ of 4.66%, which was considerably higher than the DSSC fabricated using pure ZnO NPs photoanode (ƞ = 2.01%). The increment in photocurrent density (Jsc) could be ascribed to the perfect band alignment of NiO and Co3O4 NPs in the ternary NC. Further, the ZnO/NiO/Co3O4 NC photoanode integrated DSSC disclosed 97% retainment in energy conversion efficiency even after 10 days of operation. The electrochemical performance of supercapacitor fabricated using ternary ZnO/NiO/Co3O4 NC showed high specific capacitance of 534.7 Fg−1 at 1 Ag−1 with favourable rate ability (∼52% at 16 Ag−1), good cyclic stability (91.07%) and low internal resistance. Moreover, the ZnO/NiO/Co3O4 NC at a current density of 2 Ag−1 exhibited a significantly high capacitance value of 463.1 Fg−1, which was 1.93, 1.58 and 1.22 times greater than ZnO NPs, ZnO/Co3O4 NC and ZnO/NiO NC, respectively.

Ni-Mo bimetallic oxides/rGO nanocomposites as counter electrode for the application of DSSCs

The one-pot chemical reduction process was used to generate the bimetallic Ni–Mo nanoparticles attached to reduced graphene oxide (rGO) nanocomposite, which was then used as an effective counter electrode in dye-sensitized solar cells (DSSC). Diffraction patterns were used to investigate the face-centered crystalline structure of the spherical-shaped Ni–Mo nanoparticles that were uniformly anchored over the surface of rGO. The nanoparticles had an average diameter ranging from 70 to 120 nm. Raman spectroscopy was utilized to investigate the structural interaction that was created by the presence of bimetallic nanoparticles and the graphene oxide support. In addition, the rGO/Ni–Mo counter electrode equipped DSSC demonstrated the highest solar to electrical energy conversion efficiency of 3.11% under irradiation from one sun with a fill factor (FF) of 0.48.

Two-Coordinate Thermally Activated Delayed Fluorescence Coinage Metal Complexes: Molecular Design, Photophysical Characters, and Device Application.

Since the emergence of the first green light emission from a fluorescent thin-film organic light emitting diode (OLED) in the mid-1980s, a global consumer market for OLED displays has flourished over the past few decades. This growth can primarily be attributed to the development of noble metal phosphorescent emitters that facilitated remarkable gains in electrical conversion efficiency, a broadened color gamut, and vibrant image quality for OLED displays. Despite these achievements, the limited abundance of noble metals in the Earth's crust has spurred ongoing efforts to discover cost-effective electroluminescent materials. One particularly promising avenue is the exploration of thermally activated delayed fluorescence (TADF), a mechanism with the potential to fully harness excitons in OLEDs. Recently, investigations have unveiled TADF in a series of two-coordinate coinage metal (Cu, Ag, and Au) complexes. These organometallic TADF materials exhibit distinctive behavior in comparison to their organic counterparts. They offer benefits such as tunable emissive colors, short TADF emission lifetimes, high luminescent quantum yields, and reasonable stability. Impressively, both vacuum-deposited and solution-processed OLEDs incorporating these materials have achieved outstanding performance. This review encompasses various facets on two-coordinate TADF coinage metal complexes, including molecular design, photophysical characterizations, elucidation of structure-property relationships, and OLED applications.

Converting CO2 to single-cell protein via an integrated electrocatalytic-biosynthetic system

Boosting CO2 biotransformation by renewable electrical energy provides a prospective avenue to reform the biomanufacturing paradigm and achieve a circular carbon economy. However, mismatches between electrocatalytic and biosynthetic modules lead to poor efficiency. Herein, we design an integrated electro-driven CO2-single cell protein (SCP) transformation system, via coupling an electrocatalytic CO2 reduction to formate module with a formate assimilation module. A Cu/Cu2O electrocatalyst has been rationally designed with excellent duration stability over 100 h under −0.78 VRHE. Strain adaptability investigation and equipment upgrading are carried out to guarantee the effective integration. SCP has been accumulated to a OD600 of 4 with an exponential growth rate of 0.114 OD h−1 and electrical energy conversion efficiency of 9.2%. No risky hydrogen is needed and the produced formate is ready-to-use for biosynthesis. The elaborate construction bridges non-biological and biological carbon fixation units and offers a promising blueprint for electro-driven CO2 biotransformation and scalable bio-manufacturing.

A numerical study on the effect of employing porous medium on thermal performance of a PV/T system

Surface temperatures of photovoltaic (PV) panels increase with solar radiation and ambient temperature. This temperature increase negatively affects the PV cell, causing the electrical efficiency of the system to decrease. Photovoltaic-thermal (PV/T) systems also provide thermal energy gain by cooling PV cells, increasing electrical conversion efficiency and lifespan. Integrating porous material into cooling pipes offers an important innovation in terms of the cooling techniques of PV panels. This study emphasizes the positive effects of porous materials by innovative approaches in this field. For this reason, in order to increase the electrical and thermal efficiency of PV cells, a porous material-supported cooling system was designed for the PV/T system and the effects of using porous materials with different properties were examined with Ansys Fluent software. As the porous density and porosity ratio of the porous material used throughout the pipe decreased, the average cell temperature decreased and the water outlet temperature increased. At a low flow rate of 0.3 L/min, it achieved an improvement of approximately 118% in thermal efficiency compared to the pipe without porous material. The porous structure containing 0.9 and 30 PPI pore density reached the highest efficiency value of 96.56% with a flow rate of 1.71 L/min.

Waste heat recovery from the biomass engine for effective power generation using a new array-based system

Thermoelectric generator (TEG)-thermosyphon-based heat recovery system (HRS) for harvesting the heat from the high temperature sources is a well-known technology for power generation. However, various thermal resistances (a total of nine) are involved in the thermosyphon-based HRS between the heat sources and TEGs which generate irreversibility that ultimately reduces its performance. In this work, a new design of HRS i.e. TEG-array-based is proposed for effective power generation even at low temperatures of sustainable heat source by minimizing the thermal resistances. This TEG-array-based HRS is driven by a salt gradient thermal storage device (SGTSD) which is used for efficiently recovering and storing of sustainable waste heat generated from a biomass(renewable energy)-based engine-generator. The proposed system is experimentally studied to analyse the temperature variations in SGTSD, characteristics of sustainable waste heat temperature, and performance features of TEGs in terms of obtained electrical parameters, output power and conversion efficiency. The experimental results showed that the maximum open circuit voltage, output power and conversion efficiency of TEG are obtained as 81.62V, 7.438W and 4.63\\% respectively. With this proposed system, seven thermal resistances (out of total nine) are totally eliminated while the others two are lowered that leads to effectively transfer the energy from sustainable heat source to TEGs via minor equivalent thermal resistance of 0.01198oC/W. The proposed system is found to be capable of charging a 12 V, 80 Ah heavy-duty battery for real life applications.

Constructing independent CNTs conductive network to boost combustion performance of metastable intermixed composites

AbstractNovel metastable intermixed composites (MICs) constructed by carbon nanomaterials are expected to achieve high energy content and high combustion efficiency, but traditional preparation technologies always bring barely improvement in performance. Herein, novel PVDF/CuO/Al@CNTs MICs with independent continuous carbon nanotubes (CNTs) conductive networks were prepared by thoroughly utilizing the conductivity and photothermal properties of CNTs. A conductive network can be constructed at the interface of each encapsulated PVDF/CuO/Al particle with the addition of >0.5 wt% CNTs. The great increase in electrical and thermal conductivity of PVDF/CuO/Al@CNTs MICs indicates excellent energy transfer efficiency across the sample. Significant enhancement of the combustion reaction has been achieved, with the minimum ignition energy and ignition delay time of PVDF/CuO/Al@CNTs3 reduced by ~31% and ~50%, respectively. This indicates that the CNTs with unique photothermal properties can be utilized as an effective igniter. Moreover, the optimal PVDF/CuO/Al@CNTs1 MICs enhanced the pressurization rate (~300%), energy output (~55%), and combustion velocity (~200%). The mechanism of the fast combustion reaction can also be discussed by the weak interface interaction and the energy conductive of the CNTs network throughout the sample. This work provides a modern strategy for strong combustion MICs that can be generalized and applied in the field of energetic materials.Highlights An independent continuous CNTs conductive network was prepared with a small amount of CNTs. The electrical and heat conversion efficiency is greatly improved. CNTs with unique photothermal properties can be utilized as an effective igniter. The laser sensitivity is improved, and the reaction energy, pressure, and pressure rates are significantly increased. The combustion performance was significantly improved, and more intense, and the combustion speed was significantly increased.

Adaptive bicycle: A novel approach to design a renewable and energy-efficient electric bicycle with manual charging

This study focuses on developing an adaptive bicycle prototype with a manual charging mechanism for renewable energy. In response to environmental concerns and the demand for eco-friendly transportation, the research introduces a sustainable approach for short-distance travel. The goal is to demonstrate human power as an effective alternative to non-renewable energy by converting cycling’s rotational force into electrical energy. This energy is stored in a specialized battery and used to power the bicycle with an electric motor’s assistance. The methodology involves constructing and testing a prototype to capture and store energy during pedaling, analyzing mechanical components, electrical conversion, and battery efficiency. Controlled experiments assess the adaptive bicycle’s functionality and effectiveness in self-charging without external power. Results indicate successful integration of the manual charging mechanism with an average energy conversion efficiency of X%. The adaptive bicycle offers a sustainable solution for short-distance commuting, minimizing environmental impact and promoting an eco-friendly mode of travel. This innovative approach highlights the integration of renewable energy into everyday transportation, addressing environmental concerns by reducing dependence on non-renewable sources.

Development of Triboelectric Nanogenerators Using Novel 3D Printed Polymer Materials

Triboelectric nanogenerators (TENGs) are becoming attractive devices for harvesting mechanical energy. 3D printing (3DP) is a newly reported technique for the development of this device. This technique is not fully explored for the fabrication of triboelectric materials and compatible printing processes. Herein, three main 3DP techniques including powder‐based multijet fusion, resin‐based polyjet fusion, and filament‐based fused deposition modeling are utilized to investigate new sets of 3DP triboelectric materials. Mechanical to electrical conversion efficiency of 3D printed and commercially available negative and positive triboelectric materials are compared and investigated. Polyamide ‐12 (PA12), Veroclear, acrylonitrile‐styrene‐acrylate (ASA), copper‐coated polylactic acid (Cu‐PLA), polycarbonate (PC), and polyethylene terephthalate glycol (PETG) are fabricated using compatible 3D printing techniques. 3D‐printed PA12 is considered as a reference positive triboelectric layer. Meanwhile, 3D‐printed Veroclear, ASA, Cu‐PLA, PC, PETG, and commercial materials like Teflon sheets, PA6,6 conductive sheets, indium tin oxide‐coated polyethylene terephthalate, conductive‐nylon sheets, and PVDF membrane are selected as negative triboelectric materials. The maximum AC voltage of 80 V and maximum instantaneous current of 0.9 μA are produced by pairing 3DP‐PA12 and 3DP‐Veroclear under open circuit condition. This AC output is further converted to DC output using brdige rectifier circuitry to efficiently charge up the capacitor and glow series of 16 LEDs.

Design and analysis of an electromagnetic energy conversion device

In this study,we introduces an innovative device designed for wave-heat-electricity conversion, incorporating a classical split-ring resonator (SRR) and a Bi2Te3 semiconductor strip. This configuration is adept at absorbing electromagnetic energy, transforming it into thermal energy, and facilitating an electrical response. The paper delves into the detailed physical modeling and operational principles of the device. We begin by employing an equivalent circuit model to analyze the SRR's transmission characteristics and its temperature response under specific conditions. The investigation further extends to examining how structural dimensions and material properties affect the development of a local hotspot, leading to the refinement of the SRR resonant unit. We then integrate a Bi2Te3 semiconductor strip beneath this hotspot, enhancing the device's conversion capabilities. Our findings indicate an absorption efficiency of 0.085 at 2.45 GHz, a remarkable thermal conversion efficiency of 172.8 °C/W, and an electrical conversion efficiency of 0.195 mV/°C, all measured at an input power of 7 W. This research not only demonstrates the efficacy of the proposed device in wave-heat-electricity conversion but also provides a comprehensive reference for future advancements in this field.

Impacts of thermal and electric contact resistance on the material design in segmented thermoelectric generators

Segmented thermoelectric generators (STEGs) can exhibit present superior performance than those of the conventional thermoelectric generators. Thermal and electrical contact resistances exist between the thermoelectric material interfaces in each thermoelectric leg. This may significantly hinder performance improvement. In this study, a five-layer STEG with three pairs of thermoelectric (TE) materials was investigated considering the thermal and electrical contact resistances on the material contact surface. The STEG performance under different contact resistances with various combinations of TE materials were analyzed. The relationship between the material sequence and performance indicators under different contact resistances is established by machine learning. Based on the genetic algorithm, for each contact resistance combination, the optimal material sequences were identified by maximizing the electric power and energy conversion efficiency. To reveal the underlying mechanism that determines the heat-to-electrical performance, the total electrical resistance, output voltage, ZT value, and temperature distribution under each optimized scenario were analyzed. The STEG can augment the heat-to-electricity performance only at small contact resistances. A large contact resistance significantly reduces the performance. At an electrical contact resistance of RE = 10–3 K·m2·W−1 and thermal contact resistance of RT = 10–8 Ω·m2, the maximum electric power was reduced to 5.71 mW (90.86 mW without considering the contact resistance). And the maximum energy conversion efficiency is lowered to 2.54% (12.59% without considering the contact resistance).

Analysis and Design of Small-Impact Magnetoelectric Generator

For projectile impact penetration experiment, batteries or capacitors are usually used as power sources for projectile-borne recording devices. However, these power sources are easy to fail under high impact. In this paper, a small-impact magnetoelectric generator is introduced, which converts impact force into electrical energy to supply power for devices. The influence of generator structure on force–electricity conversion efficiency is analyzed. Based on the analysis, a small-impact magnetoelectric generator with double springs and two-part coils is designed. A hammer test is carried out on the generator. The test results show that this generator structure would achieve higher force–electricity conversion efficiency under small space.

Thermodynamic analysis of an air liquid energy storage system coupling Rankine cycle and methane steam reforming to improve system electrical conversion and energy efficiency

To solve the problem of the low electro-electric conversion efficiency of air liquid energy storage (LAES) systems and the low energy and exergy efficiency of LAES coupled with solar energy, a LAES system coupled with Rankine cycle and steam methane reforming system has been proposed. The system utilizes solar energy and couples the Rankine cycle to enhance power generation. The coupled steam methane reforming subsystem utilizes low temperature heat that is unavailable from the Rankine cycle for methane reforming to produce efficient fuel hydrogen. The article established the LAES and Rankine thermodynamic models, the economic model, and the solar heat flow test device for analytical studies. The findings indicate that the coupled system attains a staggered energy utilization, exhibiting a notably high exergy efficiency of 59.63%. This represents a marked enhancement of 15.45% when compared to the LAES system coupled with solar energy. The proposed system boasts an electro-electric conversion efficiency of 140.24%, demonstrating a remarkable 71.43% enhancement over the LAES-alone system. Moreover, the 1 MW system can produce up to 522.11 kg/h of hydrogen, the static payback period of the system is 6.12 years and the internal rate of return of the system can be 23.28%.

Optimal planning and design of waste-to-energy plant for aquaculture systems

Background: Several aquaculture industries in underdeveloped nations use fossil fuel-powered generators to produce electricity. This pattern has raised greenhouse gas emissions as well as the price of aquaculture products. Methods: To address this issue, this study contains a bi-objective model that optimizes the parametric settings of waste-to-energy (WTE) plants for aquaculture firms: Levelized cost of energy and power expenses for reverse logistics. The best values for these objectives were created using a genetic algorithm and goal programming. Results: Four planning periods were taken into account during implementation, and actual data were gathered from a Nigerian aquaculture company. The electricity costs from biodiesel ranged from N0.7541 per kW to N0.7628 per kW, respectively. Reverse logistics has energy costs ranging from N6 329 492.10 to N7 121 015.53. The proposed model produced average values for several WTE parametric parameters, including a 1.69 million kg hydrogen gas, a 59.16% hydrogen gas compression efficiency, and an 83.39% electricity conversion efficiency. Furthermore, the system had logistics’ minimum and maximum fractions of 0.18% and 21%, respectively. Conclusion: Our findings demonstrated how WTE parametric parameters impact the aquaculture industry’s electrical power unit.

Exergy and economic analysis of a photovoltaic panel cooling with air bubble induced water jacket

Solar photo voltaic (PV) panel performance is greatly affected by the rise in temperature of the PV panel. To increase the electrical conversion efficiency of the PV panel, assessments are made under various cooling circumstances. To assess the efficacy of the PV panel using a water-cooling system in the climate of Manipal, India, experimental studies were conducted in this research. The purpose of this research is to evaluate and compare various cooling strategies, such as Heat sink, water jacket, air bubble cooling and combination of these techniques. Air bubbles are introduced inside the cooling jacket, which generates turbulence motion and cools the PV panel. The cooling system is inspected while running at different panel temperatures. The percentage drop in maximum panel temperature is found to be highest at 15.36 % for the panel attached with water jacket and air bubble with heat sink combination. Also, the power output of the panel is found to be the highest for the above combination with the increase of 9.31%.

Fabrication of Ceramic-Polymer Piezo-Composites with Triply Periodic Minimal Interfaces via Digital Light Processing

The geometry of the phase interface in co-continuous piezoelectric composites is critical in improving their piezoelectric properties. However, conventional co-continuous piezoelectric composites are mostly simple structures such as wood stacks or honeycombs, which are prone to stress concentrations at the joints, thus reducing the fatigue service performance and force–electric conversion efficiency of piezoelectric composites. Such simple structures limit further improvements in the overall performance of co-continuous piezoelectric composites. In this study, based on the digital light processing 3D printing method, we investigated the influence of three different structures–the gyroid, diamond, and woodpile interfaces–on the piezoelectric and mechanical properties of co-continuous ceramic/polymer piezoelectric composites. These findings demonstrate that the gyroid and diamond interfaces outperformed the ceramic skeleton of the woodpile interface in terms of both mechanical and electrical properties. When the ceramic volume percentage was 50%, the piezo-composite of the gyroid surface exhibited the greatest hydrostatic figure of merit (HFOM), reaching 4.23×10−12 Pa−1, and its piezoelectric coefficient (d33) and relative dielectric constant (εr) reached 115 pC/N and 748, respectively. The research results lay the foundation for the application of co-continuous piezoelectric composites in underwater communication and detection.

An experimental investigation on thermal energy storage characteristics of nanocomposite particles dispersed phase change material for solar photovoltaic module cooling

Electrical conversion efficiency of a solar photovoltaic (SPV) module suffers due to increase in its temperature. An integration of thermal energy storage system with phase change material (PCM) in a SPV module will improve its overall efficiency by maintaining its temperature. Though, Paraffin is the most common PCM for SPV cooling application, its low thermal conductivity limits its performance. Thermal performance of the Paraffin can be enhanced by utilizing high conductive nanocomposite particles. In the present research work, the enhancement in thermal characteristics of Paraffin by dispersing titanium dioxide - silver nanocomposite particles are examined. Titanium dioxide - silver nanocomposite particles (NP) are synthesized using sol-gel process and characterized using standard techniques. The effect of dispersing titanium dioxide - silver nanocomposite particles (NP) in 0.5, 1, and 1.5 % mass concentrations with thermal cycling on thermal conductivity and hence the storage performance of Paraffin are investigated. Further, the chemical, physical and thermal stabilities of nanocomposite particles dispersed Paraffin (NCDPWX) are examined. When compared to the base Paraffin, the cycled NCDPWX with 1 wt% NP exhibits a better thermal conductivity (0.384 W/mK), melting heat capacity (128 kJ/kg), freezing heat capacity (119.46 kJ/kg), melting time (6.07 min), freezing time (10.11 min), thermal stability up to 352 °C, substantial reduction in degree of super cooling (3.96 °C), impregnation ratio (102.64 %), impregnation efficiency (100.92 %), thermal storage capability (98.31 %) and better chemical stability. Overall, the synthesized NCDPWX is a suitable thermal energy storage material for cooling of SPV modules.

Investigating the modified thermoelectric generator system performance

AbstractIt is essential to enhance the performance of the thermoelectric generator as lower efficiencies are obtained recently. This could be achieved by changing its dimensions in addition to copper strip thickness. The present study is performed to obtain the best dimensions of the P–N legs considering the interaction between all variables. To do this, a comprehensive TEG model is achieved in addition to utilizing the single-objective optimization technique. The main performance metrics, including electricity production and conversion efficiency, are assessed, and contrasted with the conventional TEG system since the simulation. The length of the legs and their cross-sectional area were shown to significantly affect power production. The thickness of the conducting plate, in contrast, barely matters. For instance, a P–N pair with legs that have a 2 mm2 cross-sectional area generates 0.4 W and 1.3 W for temperature differences of 480 °C and 980 °C, respectively. Furthermore, the equivalent efficiencies are 4.41% and 6.73%, respectively. Using the genetic algorithm revealed that the ideal values for the leg cross section, leg length, and conducting plate thickness are 1.84 mm2, 0.5 mm, and 0.44 mm, respectively. Once compared to the conventional system, using the optimization method results in an improvement in power production and conversion efficiency of about 247% at a temperature differential of 980 °C.